DS200CDBAG1BBB  | 连接器  |  提供电源和信号

型号：DS200CDBAG1BBB

输入电压范围:12-48VDC

输出电压范围:5VDC。

输出电流:最大10A。

效率:大于90%。

尺寸:170mm x105mmx32mm.

重量:约120g。

运行温度:-20°C至+50°C。

存储温度:-40°C至+70°C。

环境湿度:5%至95%相对湿度(无凝露)

产品描述

GE接触器驱动板DS200CDBAG1BBB是为其Mark V系列创建的，其特定应用是打开和关闭单个接触器。所有电源、输入信号和输出信号都通过板上的 1 个连接器 （1TB） 连接到DS200CDBAG1BBB板。1TB 连接器由四个部分组成，这四个部分标记为 1TBA、1TBB、1TBC 和 1TBD。总共三个插头连接器为连接器提供电源和信号。要卸下连接器，请使用螺丝刀帮助将连接器从电路板上撬开。在从此DS200CDBAG1BBB DS200CDBAG1BBB接触器驱动器的组件中卸下任何类型的任何电缆或连接器之前，最好是标记所有电缆，以避免在安装更换板时造成混淆。

此外，电路板上还有一个保险丝连接器。如果需要更换，请使用 4 安培 125V、2 AG 慢熔保险丝。 如果保险丝经常熔断，您可能会怀疑需要更换电路板。如果您怀疑电路板无法正常工作，则可能需要对电路板进行故障排除。板载测试点供您测试电路板的各种功能。您需要使用隔离的测试设备来测试电路板。一个点是共同的参考点。第二个测试点用于15 V直流电源基准。第三个是接触器驱动器参考。

Model: DS200CDBAG1BBB

Input voltage range :12-48VDC

Output voltage range :5VDC.

Output current: Max. 10A.

Efficiency: greater than 90%.

Size :170mm x105mmx32mm.

Weight: About 120g.

Operating temperature :-20°C to +50°C.

Storage temperature :-40°C to +70°C.

Ambient humidity :5% to 95% relative humidity (no condensation)

Product description

The GE contactor driver board DS200CDBAG1BBB was created for its Mark V series with a specific application of opening and closing individual contactors. All power, input and output signals are connected to the DS200CDBAG1BBB board via a connector (1TB) on the board. The 1TB connector consists of four parts, which are labeled 1TBA, 1TBB, 1TBC and 1TBD. A total of three plug connectors provide power and signal to the connector. To remove the connector, use a screwdriver to help pry the connector away from the board. Before removing any cables or connectors of any type from the assembly of this DS200CDBAG1BBB DS200CDBAG1BBB contactor driver, it is advisable to mark all cables to avoid confusion when installing replacement plates.

In addition, there is a fuse connector on the board. If replacement is required, use a 4 amp 125V, 2 AG slow fuse. If the fuse blows frequently, you may suspect that the board needs to be replaced. If you suspect that the board is not working properly, you may need to troubleshoot the board. Onboard test points allow you to test various functions of the board. You need to use isolated test equipment to test the board. A point is a common reference point. The second test point is for the 15 V DC power supply benchmark. The third is the contactor driver reference.