DS200ADPAG1A  |   适配器板  |  具有一个 3 针连接器

型号：DS200ADPAG1A

输入电压范围:12-48VDC

输出电压范围:5VDC。

输出电流:最大10A。

效率:大于90%。

尺寸:170mm x105mmx32mm.

重量:约120g。

运行温度:-20°C至+50°C。

存储温度:-40°C至+70°C。

环境湿度:5%至95%相对湿度(无凝露)

产品描述

DS200ADPAG1A 虽然描述各种固定闩锁的功能当然很重要，这些锁存器对这款 DS200ADPAG1A Genius 适配器板的正常功能至关重要，但以下对此过程的如此详细的描述更有可能证明这款 DS200ADPAG1A Genius 适配器板在线的相对稀有性，以及其相关说明手册材料的稀有性。考虑到这一点，此页面上的许多特定于产品的硬件信息将来自对产品的彻底的、由技术人员主导的目视检查，以及从功能DS200ADPAG1A产品编号本身收集的任何信息。

硬件提示和建议

GE Genius 适配器板DS200ADPAG1A具有一个 40 针连接器和一个 26 针连接器。它还具有一个 3 针连接器和一个 10 针连接器。连接到 40 针连接器和 26 针连接器的电缆通过连接器内置的固定闩锁固定到位。但是，在更换电路板的过程中，在使用闩锁之前需要注意一些特殊事项。固定闩锁必须完全接合，以防止电缆与板上的连接器断开连接。DS200ADPAG1A要使用固定闩锁，请用手指将闩锁从电缆上滑开。然后，抓住连接器端的电缆，轻轻地将其从电路板上取下。要安装电缆，请先将闩锁移开，然后再将电缆插入连接器。

Model: DS200ADPAG1A

Input voltage range :12-48VDC

Output voltage range :5VDC.

Output current: Max. 10A.

Efficiency: greater than 90%.

Size :170mm x105mmx32mm.

Weight: About 120g.

Operating temperature :-20°C to +50°C.

Storage temperature :-40°C to +70°C.

Ambient humidity :5% to 95% relative humidity (no condensation)

Product description

While it is certainly important to describe the functions of the various fixing latches that are essential to the proper functioning of this DS200ADPAG1A Genius adapter board, But such a detailed description of the process below is more likely to demonstrate the relative rarity of the DS200ADPAG1A Genius adapter board online, as well as the rarity of its associated manual materials. With that in mind, much of the product-specific hardware information on this page will come from a thorough, technically-led visual inspection of the product, as well as any information gleaned from the functional DS200ADPAG1A product number itself.

Hardware tips and suggestions

The GE Genius adapter board DS200ADPAG1A has a 40-pin connector and a 26-pin connector. It also has a 3-pin connector and a 10-pin connector. The cables that connect to the 40-pin connector and 26-pin connector are secured in place by a retaining latch built into the connector. However, in the process of replacing the circuit board, some special considerations need to be paid attention to before using the latch. The fixed latch must be fully engaged to prevent the cable from disconnecting from the connector on the board. DS200ADPAG1A To use a fixed latch, slide the latch away from the cable with your finger. Then, grab the cable at the connector end and gently remove it from the board. To install the cable, remove the latch before inserting the cable into the connector.