IC695PBM300  |  实现数据交换 | 可编程自动化控制器 （PAC） 系列

该IC695BPM300是 Profibus Master 模块，以前由 GE 智能平台 （GE IP） 制造，现在隶属于艾默生自动化的 PACSystems RX3i 可编程自动化控制器 （PAC） 系列。该模块用于通过Profibus网络实现数据交换，最大输入数据为3,584字节，输出数据为3,584字节。该 Profibus 主模块支持多达 125 个 DP 从机的通信，每个 DP 从机可以发送 244 字节的输入数据并接收 244 字节的输出数据。

该IC695BPM300特别支持所有标准数据速率，9.6 kBit/s、19.2 kBit/s、93.75 kBit/s、187.5 kBit/s、500 kBit/s、1.5 MBit/s、3 MBit/s、6 MBit/s 和 12 MBit/s。它可以提供状态信息，如从站状态位阵列表、网络诊断计数器、DP 主诊断计数器、固件模块修订版和从站诊断地址。它安装在 RX3i 背板上，并支持 PCI 连接。具体而言，它必须安装在通用背板中，主机 PACSystem RX3i 控制器运行固件版本 2.9 或更高版本。它消耗的背板电流为 440 mA @ 3.3 VDC。

该模块配有 Profibus OK ED 指示器;网络指标;和 MOD 状态指示器。该模块支持同步和冻结模式以及 Profibus DP-V1 读、写和报警消息。IC695BPM300带有可升级的固件，该固件通过WinLoader软件实用程序通过主机控制器间接接收。

该模块必须在 0 至 60 摄氏度的温度范围内运行，而模块的存储温度为 -40 至 85 摄氏度。

The IC695BPM300 is a Profibus Master module formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation's PACSystems RX3i Programmable Automation Controller (PAC) family. The module is used for data exchange over the Profibus network with a maximum input data of 3,584 bytes and output data of 3,584 bytes. The Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

The IC695BPM300 specifically supports all standard data rates, 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s and 12 MBit/s. It can provide status information such as the slave status bit array table, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses. It is installed on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed in a universal backplane with the host PACSystem RX3i controller running firmware version 2.9 or higher. It consumes 440 mA @ 3.3 VDC backplane current.

The module is equipped with Profibus OK ED indicator; Network indicators; And MOD status indicator. The module supports sync and freeze modes as well as Profibus DP-V1 read, write, and alarm messages. The IC695BPM300 comes with upgradable firmware, which is received indirectly through the host controller via the WinLoader software utility.

The module must operate in a temperature range of 0 to 60 degrees Celsius, while the storage temperature of the module is -40 to 85 degrees Celsius.