IC200ALG263  |  模拟量输入模块   |  提供模拟量转485功能

零件编号 ：IC200ALG263

产品描述 ：模拟量输入模块

输入数量 ：15、单端

组数 ；1

输入电压： -10 伏至 10 伏

GE Fanuc IC200ALG263模拟量输入模块带有 15 个单端输入通道，可连接 15 个电压输入。它从PLC背板的电源接收电源，背板电源足以操作模块。不需要额外的电源。但是，需要外部电源才能为系统中的收发器供电。该模块的一些特性包括 15 位转换器分辨率、软件可配置操作和一组单端输入通道。它还为主机接口提供 15 字的模拟输入数据。背板额定电流消耗为 5 伏，最大值为 150 毫安。IC200ALG263模拟输入模块提供 250 V AC 连续用户输入至逻辑隔离，以及 1500 V AC 用户输入至 1 分钟接地隔离。“OK”指示灯 LED 表示配置和上电过程成功，但不能指示模块的硬件错误和故障。

IC200ALG263模拟量输入模块是一款将远程现场的模拟量信号采集至计算机的设备，其利用RS-485总线作为数据通信线路，提供模拟量转485功能，能够同时将模拟量输入至模块，并通过RS-485总线传输至计算机。

IC200ALG263 模拟量是表示在一定范围内连续变化的任意取值，跟数字量是相对立的一个状态表示。通常模拟量用于采集和表示事物的电压电流或者频率等参数。模拟量输入模块能够采集模拟量（如电压、电流、热电偶、热电阻、温度等数值）并通过485总线传输到电脑上。由于采用RS-485接口作为通信接口，它能够多个模块组合传输更多路数模拟量信号，并且能够在485线路上分散配置，采用地址码进行区分，可以直接接入MODBUS RTU协议的组态软件。

Part number: IC200ALG263

Product description: analog input module

Input quantity: 15. Single end

Number of groups; 1

Input voltage: -10 V to 10 V

The GE Fanuc IC200ALG263 analog input module has 15 single-ended input channels that can be connected to 15 voltage inputs. It receives power from the PLC backplane's power supply, which is sufficient to operate the module. No additional power is required. However, an external power supply is required to power the transceiver in the system. Some of the module's features include 15-bit converter resolution, software configurable operation, and a set of single-ended input channels. It also provides 15-word analog input data to the host interface. The backplane has a rated current consumption of 5 volts and a maximum of 150 mA. The IC200ALG263 analog input module provides 250 V AC continuous user input to logical isolation and 1500 V AC user input to 1-minute ground isolation. The "OK" indicator LED indicates that the configuration and power-on process was successful, but cannot indicate hardware errors and faults of the module.

IC200ALG263 analog input module is a device that collects analog signals from remote field to computer, which uses RS-485 bus as a data communication line to provide analog to 485 function, which can simultaneously input analog to the module and transmit it to the computer through RS-485 bus.

The analog quantity of IC200ALG263 is an arbitrary value that indicates continuous change within a certain range, and is a state representation opposite to the digital quantity. Analog quantities are usually used to capture and represent parameters such as voltage, current or frequency of things. Analog input module can collect analog values (such as voltage, current, thermocouple, thermal resistance, temperature, etc.) and transmit to the computer through the 485 bus. As the RS-485 interface is used as the communication interface, it can combine multiple modules to transmit more analog signals, and can be distributed on the 485 line, using the address code to distinguish, and can directly access the configuration software of MODBUS RTU protocol.