IS200CABPG1BAA  | 控制组件背板（CABP） J13-J21 是背板上的实际卡槽

型号：IS200CABPG1BAA

系列：控制组件背板（CABP）

制造者：通用电气工业系统

功能缩略语/缩写： BPIB公司

型号类型： IGBT驱动桥式接口板

直流母线电压反馈 VCO 范围： 0-20兆赫

电源要求 ：17.7 VAC 或 5 VDC

IGBT驱动卡接口电源输出： 隔离式 5 VDC，最大 500 马

产品描述

该IS200CABPG1BAA是通用电气为其创新系列制造的控制组件背板（CABP）。

IS200CABPG1BAA通常是创新系列机架组件上背板的替换板。机架不随本板一起提供，需单独出售。机架为正在安装的电路板提供额外的安装点。其他 PCB 插入IS200CABPG1BAA上的 5 个插槽，并允许与外部信号交互和接口。该板提供与这些外部接口组件的连接。这些连接包括 ISBus 端口、电源输入、诊断工具、前面板键盘和前面板仪表。

IS200CABPG1BAA 的插头设计为不允许非板连接意外插入错误的插孔。插入背板的 PCB 应小心安装，因为虽然它们确实使用不同的单独键控连接，但很容易通过将其滑入错误的插槽而损坏电路板。背板上的插槽 1 分配给 BAIA 板。插槽 2 分配给 DSPX 板。插槽 3 指定用于 GBIA/PBIA 模块的ACL_板。插槽 4 用于BIC_板。插槽 5 用于 BPI_ 或 FOSA 板。有两个标记为 E1 和 E2 的刺入式连接器连接到 GND。还有另外两个标记为 E3 和 E4 的刺入式连接器进入 CCOM。这个板上有 21 个跳线。J1-J12 跳线是外部接口。J13-J21 是背板上的实际卡槽。

Model: IS200CABPG1BAA

Series: Control Component Backplane (CABP)

Manufacturer: General Electric Industrial Systems

Functional acronym/abbreviation: BPIB Corporation

Model type: IGBT drive axle interface board

Dc bus voltage feedback VCO range: 0-20 MHZ

Power requirements: 17.7 VAC or 5 VDC

IGBT driver card interface power output: isolated 5 VDC, Max 500 ma

Product description

The IS200CABPG1BAA is a control component backplane (CABP) manufactured by GE for its innovative family.

The IS200CABPG1BAA is usually a replacement board for the backplane on the innovative series of rack components. Racks are not supplied with this board and must be sold separately. The rack provides additional mounting points for the boards being installed. Other PCBS plug into five slots on the IS200CABPG1BAA and allow interaction and interface with external signals. The board provides connections to these external interface components. These connections include ISBus ports, power inputs, diagnostic tools, front panel keyboards, and front panel meters.

The IS200CABPG1BAA's plug is designed to not allow a non-board connection to accidentally insert the wrong jack. PCBS inserted into the backplane should be installed with care, because while they do use different individual keying connections, it is easy to damage the board by sliding it into the wrong slot. Slot 1 on the backplane is allocated to the BAIA board. Slot 2 is allocated to the DSPX board. Slot 3 specifies the ACL_ board for the GBIA/PBIA module. Slot 4 is for the BIC_ board. Slot 5 is used for BPI_ or FOSA boards. There are two spiked connectors labeled E1 and E2 connected to GND. There are two other thrust-type connectors labeled E3 and E4 that enter CCOM. There are 21 jumpers on this board. J1-J12 jumpers are external interfaces. J13-J21 is the actual card slot on the backplane.