DS200IIBDG1AEA   |  绝缘栅双极晶

品牌： GE发那科

制造者 ：通用电气发那科;艾默生自动化 （Current）

制造者 ：GE发那科

零件编号 ：DS200IIBDG1AEA

产品描述： 绝缘栅双极晶体管

GE 绝缘栅双极晶体管 （IGBT） 板DS200IIBDG1AEA包含 9 个指示灯 LED，可在运行时提供电路板的状态。LED 从电路板机柜内部可见，点亮时呈红色。 请注意，由于您只能在机柜门打开的情况下看到 LED，并且当驱动器通电时，您必须遵守一些准则以避免触电才能查看 LED。所有电路板都必须被视为高压元件，并且不得接触电路板柜中的任何东西。当门打开时，不要让任何东西掉入 Mark V 系列驱动器组件的机柜中，这一点至关重要。如果螺丝、电线或其他物品掉入机柜中，则必须断开驱动器的所有电源。然后，等待三分钟，让所有电源离开组件。然后，找到该项目并搜索可能掉入的其他零件。您可能需要用吸尘器吸出组件以确保清除所有碎屑。

GE 绝缘栅双极晶体管 （IGBT） 板DS200IIBDG1AEA包含一个 34 针连接器，您可以将带状电缆连接到该连接器。连接带状电缆时，只需从连接器上抓住电缆并将连接器压入到位。切勿握住带状电缆将带状电缆拉出。该DS200IIBDG1AEA板上包含三个 8 针连接器，连接器标记为 APL、BPL 和 CPL。 连接器的电缆在机柜内布线，并连接到机柜内的其他板和 Mark V 系列驱动器组件。这款 IIBD 缩写的 IGBT 栅极驱动器板的所有内部硬件元件都应获得该器件正常样式的印刷电路板涂层的基本保护，该涂层作为厚厚的保护层存在，可优先保护此 Mark V 系列产品组装的最关键硬件元件。

Brand: GE Fanuc

Manufacturer: General Electric Fanuc; Emerson Automation (Current)

Manufacturer: GE Fanuc

Part number: DS200IIBDG1AEA

Product description: insulated gate bipolar transistor

The GE insulated gate bipolar transistor (IGBT) board DS200IIBDG1AEA contains nine indicator leds that provide the status of the board at runtime. The LED is visible from inside the circuit board cabinet and appears red when lit. Note that since you can only see the LED with the cabinet door open, and when the drive is powered on, you must follow some guidelines to avoid electric shock before you can view the LED. All boards must be considered high voltage elements and must not touch anything in the circuit board cabinet. When the door is open, it is crucial not to let anything fall into the cabinet of the Mark V Series drive assembly. If screws, wires, or other items fall into the cabinet, all power to the drive must be disconnected. Then, wait three minutes for all power to leave the component. Then, find the item and search for other parts that may have fallen in. You may need to vacuum out the components to ensure that all debris is removed.

The GE insulated gate bipolar transistor (IGBT) board DS200IIBDG1AEA contains a 34-pin connector to which you can connect ribbon cables. To connect a ribbon cable, simply grab the cable from the connector and press the connector into place. Do not pull out the ribbon cable by holding it. The DS200IIBDG1AEA board contains three 8-pin connectors labeled APL, BPL, and CPL. The cable for the connector is routed inside the cabinet and connected to other boards and Mark V Series driver assemblies in the cabinet. All internal hardware components of this IIBD-abbreviated IGBT gate driver board shall be provided with the basic protection of the device's normal style printed circuit board coating, which exists as a thick layer of protection to prioritize the most critical hardware components assembled in this Mark V Series product.