IC697ALG230  转换器 提供串行连接器的任何 I/O 插槽

产品描述

IC697ALG230是一款 PACSystems 系列 90-30 RX3i 模拟电流输入模块，提供 16 个通道。 该模块的 16 个独立和单端通道可配置为以下三个范围中的任何一个：4 至 20 mA、0 至 20 mA 或 4 至 20 mA 增强型。每个范围都可以获得高报警和低报警。在增强型范围内，IC697ALG230模块可以设置为低报警限值，以在 4 至 20 mA 应用中通过开路故障检测来检测输入电流;用户还可以设置高警报警报。此外，此模块还报告状态，包括 CPU 的电源状态。IC697ALG230可用于 RX3i 或 90-30 系列中提供串行连接器的任何 I/O 插槽。

具体到IIC697ALG230模块，控制器背板上的 5 VCD 总线消耗 120 mA 电流。这还需要一个65 mA加电流环路，由用户提供的+24 VDC电源供电。标准更新速率为 6 ms，隔离为 250 VAC 连续或 1500 VAC 持续 1 分钟。扫描活动通道时，要扫描的通道数将按顺序完成。模拟值在转换器的整个范围内进行缩放，工厂校准可调整每比特的模拟值。RX3i 机架支持升级与此模块关联的固件，但这不包括 90-30 机架。该IC693ALG223D还配备了发出 ON、OFF 和 FAIL 的 LED 状态灯，以协助用户进行操作和故障排除。

技术规格

频道数：1 至 16 可选

输入电流范围：0 至 20 mA、4 至 20 mA 和 4 至 20 mA 增强

校准：：工厂校准为每次计数 4 μA 或每次计数 5 μA

更新速率：13 毫秒（所有 16 个通道）

输入滤波器响应：9赫兹

功耗：+5 V总线为120 mA，+24 V总线为65 mA

Product description

The IC697ALG230 is a PACSystems series 90-30 RX3i analog current input module with 16 channels. The module's 16 independent and single-ended channels can be configured in any of the following three ranges: 4 to 20 mA, 0 to 20 mA, or 4 to 20 mA enhanced. Both high and low alarms are available for each range. In the enhanced range, the IC697ALG230 module can be set to a low alarm limit to detect input current through open fault detection in 4 to 20 mA applications; Users can also set high alert alerts. In addition, this module also reports the status, including the power status of the CPU. The IC697ALG230 can be used in any I/O slot that provides serial connectors in the RX3i or 90-30 series.

Specifically for the IIC697ALG230 module, the 5 VCD bus on the controller backplane consumes 120 mA of current. This also requires a 65 mA plus current loop, powered by a +24 VDC supply provided by the user. The standard update rate is 6 ms and the isolation is 250 VAC continuous or 1500 VAC continuous for 1 minute. When scanning active channels, the number of channels to be scanned is done sequentially. Analog values are scaled across the entire range of the converter, and factory calibration adjusts the analog value per bit. RX3i racks support firmware upgrades associated with this module, but this does not include 90-30 racks. The IC693ALG223D is also equipped with LED status lights that emit ON, OFF and FAIL to assist users with operation and troubleshooting.

Technical specification

Channel number: 1 to 16 Optional

Input current range: 0 to 20 mA, 4 to 20 mA, and 4 to 20 mA enhanced

Calibration: Factory calibration to 4 μA per count or 5 μA per count

Update rate: 13 ms (all 16 channels)

Input filter response: 9 Hz

Power consumption: 120 mA for the +5 V bus and 65 mA for the +24 V bus