IC695PSD140LT 电源模块  用于需要冗余和增加容量模式的应用

品牌ge Fanuc

系列pacsystem RX3i

制造商ge发那科

产品描述电源模块

部件编号:IC695PSD140LT

输入电压范围85至264 VAC 100至300 VDC

电源模块

电源40瓦

额定电压120/240 VAC或125 VDC

输入电压范围:18 ~ 30vdc

输入功率满负载时最大60瓦

输出3

输出电压24 VDC: 19.2 VDC ~ 28.8 VDC;5.1 VDC: 5.0 VDC至5.2 VDC (5.1 VDC标称);3.3 VDC: 3.1 VDC至3.5 VDC (3.3 VDC标称)

LED指示灯

IC695PSD140LT是一个通用基础电源，可与任何RX3i中央处理器(CPU)兼容使用。该模块没有跳线或拨码开关来定义模块的操作。

IC695PSD140LT占用机箱2个槽位。它由100-240 VAC或0-125 VDC的外部供电电压供电，它提供额定输出功率40瓦，3.3 VDC时为30瓦;30瓦5VDC和40瓦24 VDC继电器。RX3i通用背板可安装多达四(4)个多用途电源，用于需要冗余和增加容量模式的应用。

当配置为负载共享架构时，安装在前面板上的IC695PSD140LT的开/关开关不能在无意中关闭。最小电源数量必须保持在“On”状态，以使系统合格。对于相同的配置，电源模块必须连接到相同的电源上。

IC695PSD140LT 电源模块  用于需要冗余和增加容量模式的应用

Brand ge Fanuc

Series pacsystem RX3i

Manufacturer ge Fanuc

Product Description Power module

Part number :IC695PSD140LT

Input voltage range 85 to 264 VAC 100 to 300 VDC

Power module

Power supply 40 watts

Rated voltage 120/240 VAC or 125 VDC

Input voltage range :18 ~ 30vdc

Maximum input power 60 watts at full load

Damage output 3

Output voltage 24 VDC: 19.2 VDC ~ 28.8 VDC; 5.1VDC: 5.0VDC to 5.2VDC (5.1VDC nominal) 3.3 VDC: 3.1 VDC to 3.5 VDC (3.3 VDC nominal)

LED indicator

The IC695PSD140LT is a universal base power supply that is compatible with any RX3i Central processing unit (CPU). The module has no jumpers or dip switches to define the module's operation.

The IC695PSD140LT occupies two slots in the chassis. It is powered by an external supply voltage of 100-240 VAC or 0-125 VDC, and it provides a rated output power of 40 watts, 30 watts at 3.3 VDC; 30 watt 5VDC and 40 watt 24 VDC relays. The RX3i Universal backplane can be installed with up to four (4) multi-purpose power supplies for applications requiring redundancy and increased capacity modes.

When configured as a load sharing architecture, the on/off switch of the IC695PSD140LT installed on the front panel cannot be unintentionally turned off. The minimum number of power supplies must be kept in the "On" state for the system to qualify. For the same configuration, the power module must be connected to the same power supply.