FBM203-P0914SV 模块  可执行所需的信号转换

概述

FBM203-P0914SV模块的每个输入通道接受2线或3线RTD传感器输入，电阻范围为0至320欧姆(FBM203)， 0至640欧姆(FBM203b)或0至30欧姆(FBM203c)。FBM203d的每个输入通道接受4线RTDsensor输入，在0到320欧姆的电阻范围内。每个模拟输入都与其他通道和地电隔离。

这些模块执行所需的信号转换，将来自现场传感器的电气输入信号连接到可选的冗余现场总线。

FBM203-P0914SV模块执行模拟输入应用程序，提供转换时间(以每个模块为基础)和可配置的变化率限制选项。两种类型的无源端接组件可用于FBM203/b/c模块:

DIN导轨安装ta，类似于其他200系列fbm使用的ta

底板安装TA，直接安装到200系列底板的现场I/O连接器上。这些ta提供现场I/O接线

当连接到适当的TAs时，FBM203-P0914SV模块提供以前由100系列FBM VO子系统提供的功能。

FBM203可以与支持I/O fbm的任何版本的oxboro Evo 2控制核心服务软件一起使用。可用于fbm203的ta在与3线RTD输入一起使用时支持100系列fbmo3a的功能。

FBM203c仅支持I/A Series@software V8.0 ~ V8.8或Control Core Servicessoftware V9.0及以上版本。可用于fbm203c的ta在与3线rtinput一起使用时支持100系列FBM33A的功能。

FBM203d仅支持ia系列软件V8.6 ~ V8.8或Control CoreServices软件V9.0及以上版本。

FBM203-P0914SV 模块  可执行所需的信号转换

summarize

Each input channel of the FBM203-P0914SV module accepts 2 - or 3-wire RTD sensor inputs with resistance ranges of 0 to 320 ohms (FBM203), 0 to 640 ohms (FBM203b) or 0 to 30 ohms (FBM203c). Each input channel of the FBM203d accepts 4 lines of RTDsensor input in a resistance range of 0 to 320 ohms. Each analog input is isolated from other channels and ground electricity.

These modules perform the required signal conversion, connecting electrical input signals from field sensors to an optional redundant fieldbus.

The FBM203-P0914SV module performs analog input applications, providing conversion times (on a per-module basis) and configurable rate-of-change limiting options. Two types of passive termination components are available for the FBM203-P0914SV module:

DIN rail mounts ta, similar to the ta used in other 200 series FBMS

Baseboard mount TA, which is mounted directly to the field I/O connector on the 200 Series baseboard. These ta's provide on-site I/O wiring

When connected to the appropriate TAs, the fbm203 /c/d module provides functionality previously provided by the 100 Series FBM VO subsystem.

The FBM203 can be used with any version of the oxboro Evo 2 Control Core Services software that supports I/O fbm. The ta available for the fbm203 supports the functionality of the 100 Series fbmo3a when used with 3-wire RTD inputs.

The FBM203c supports only I/A Series@software V8.0 to V8.8, or Control Core Servicessoftware V9.0 or later versions. The ta available for the fbm203c supports the functionality of the 100 Series FBM33A when used with the 3-wire rtinput.

The FBM203d supports only ia series software V8.6 to V8.8 or Control CoreServices software V9.0 or later.