1C31233G04  EMERSON DCS卡件 输出输入模块

型号:1C31233G04

类别:EMERSON

Emerson艾默生输入输出模块1C31233G04的四种形式如下：

形式一：具有两个端口的输入模块，两个端口分别是模拟输入端口和数字输入端口。

形式二：具有两个端口的输出模块，两个端口分别是模拟输出端口和数字输出端口。

形式三：具有一个端口的输入/输出模块，这个端口是模拟输入/输出端口。

形式四：具有一个端口的输入/输出模块，这个端口是数字输入/输出端口。

Emerson艾默生输入输出模块1C31233G04的用途如下：

接收主站命令，对现场仪表进行控制，同时将现场仪表的测量值、状态值等反馈回主站。

接收主站命令，对现场仪表进行控制，同时将现场仪表的测量值、状态值等反馈回主站，并传输到主站。

接收主站命令，对现场仪表进行控制，同时将现场仪表的测量值、状态值等反馈回主站，并传输到主站，并传输到主站。

接收主站命令，对现场仪表进行控制，同时将现场仪表的测量值、状态值等反馈回主站，并传输到主站，并传输到主站。

3在线下装程序一定要Westinghouse西屋非常谨慎。CCPP涉及Westinghouse西屋煤气、蒸汽和发电机组，都是对安全要求极高的设备。稍有不慎，轻则会出现机组退出，严重者会出现爆炸事故。来不得半点马虎。为此，针对CCPP这样的工艺特点，在下载前，必须做好充分的事故应急预案工作，制订切实有效的安全防范措施，如将该控制器控制的所有重要运行设备，如运行允许全部切换为就地运行，所有通讯点进行隔离，并将与其对应控制器有联锁关系点和不同控制器机柜的硬接线点强制，防止新旧程序在下装瞬间，回到执行状态时的初始扫描过程中，软件初始值引起失控状态值输出，导致设备误动作。为此，Westinghouse西屋程序下装工作尽量选择在机组停运期间，采用相对安全的增量下装方式，少用全下装。总之，现场调试时的程序下装思维不能照搬照抄到生产运行中，因为现场调试属于模拟运行，而生产过程中是带负荷运行。

产品详情

1）新

2)保修期:12个月!

3）包装:原包装与纸箱。

4)交货时间:付款后3天内发货

5)所有货物将在发货前进行测试。

1C31233G04  EMERSON DCS卡件 输出输入模块

Model :1C31233G04

Category :EMERSON

Emerson The four forms of the Emerson I/O module 1C31233G04 are as follows:

Form one: An input module with two ports, namely an analog input port and a digital input port.

Form two: An output module with two ports, namely an analog output port and a digital output port.

Form three: An input/output module with one port, which is an analog input/output port.

Form four: An input/output module with one port, which is a digital input/output port.

Emerson The functions of the Emerson I/O module 1C31233G04 are as follows:

Receive the command of the master station, control the field instrument, and feedback the measured value and status value of the field instrument back to the master station.

Receive the command of the master station, control the field instrument, and feedback the measurement value and status value of the field instrument back to the master station, and transmit to the master station.

Receive the command of the master station, control the field instrument, and feedback the measurement value and status value of the field instrument back to the master station, and transmit to the master station, and transmit to the master station.

Receive the command of the master station, control the field instrument, and feedback the measurement value and status value of the field instrument back to the master station, and transmit to the master station, and transmit to the master station.

3 Online down-loading procedures must be very careful with Westinghouse. CCPP involves Westinghouse gas, steam and generator sets, all of which have high safety requirements. A little careless, light will appear unit exit, serious will appear explosion accident. There must be no carelessness. To this end, in view of the process characteristics such as CCPP, before downloading, it is necessary to make adequate accident emergency plan work and formulate effective safety precautions, such as all important operating equipment controlled by the controller, such as operation allows all to be switched to local operation, and all communication points are isolated. And force the interlocking relationship points of its corresponding controller and the hard wiring points of different controller cabinets to prevent the initial scanning process when the old and new programs return to the execution state at the moment of installation, the initial value of the software will cause the output of the out-of-control status value, resulting in device misoperation. To this end, the Westinghouse process downloading work should be selected as far as possible during the outage of the unit, using a relatively safe incremental downloading method, and using less full downloading. In short, the program installation thinking during field debugging cannot be copied to the production operation, because the field debugging belongs to the simulation operation, and the production process is run with load.

Product details

1) New

2) Warranty period :12 months!

3) Packaging: original packaging and carton.

4) Delivery time: Delivery within 3 days after payment

5) All goods will be tested before shipment.