3500/15 BENTLY 半高电源模块 机械保护系统

BENTLY本特利3500/15交流和直流电源

350015是由Bently Nevada开发的高压ACIDC电源模块。该组件为半高模块，必须安装在机架左侧的指定插椿中。该组件用作本特利内华达机械状态监测系统的电源模块Q。Legacy 3500交流电源、高压交流PIM和低压交流PIM与通用交流电源和PIM(电源输入模块)不兼容。Legacy 3500高压和低压直流电源和PIM与Legacy 3500高压和低压直流电源和PIM不兼容。

3500电源是半高度模块，必须安装在框架左边特殊设计的槽口内。3500 框架可装有一个或两个电源(交流或直流的任意组合)。其中任何一个电源都可给整个框架供电。如果安装两个电源，第二个电源可做为第一个电源的备份。当安装两个电源时，上边的电源作为主电源,下边的电源作为备用电源，只要装有一个电源，拆除或安装第二个电源模块将不影响框架的运行。3500电源能接受大范围的输入电压，并可把该输入电压转换成其它3500模块能接受的电压。

对于3500机械保护系统，有以下三种电源:

交流电源

2高压直流电源口

3.低压直流电源输入电源选项:

175到264 Vac ms: (247到 373 Vac,pk)，47到63 Hz。该选项使用交流电源且为高电压(通常22OV)交流电源输入模块(PIM)。安装版本R以前的交流电源输入模块(PIM)和或版本M以前的电源模块要求电压输入∶175到250 Vac rms,

85到132 Vac ms: (120到188 Vac, pk)47到63 Hz。该选项使用交流电源并且是低电压(通

常110V)交流电源输入模块(PIM)。安装版本R以前的交流电源输入模炔(PIM)和或版本M以前的电源模炔要求电压输入:85到125Vac rms。

88到140 Vdc: 该选项使用直流电源，并且是高电压直流电源输入模块(PIM)。20到30 Vdc: 该选项是低压直流供电，是低压直流供电模炔(PIM)。

超限保护:对于所有电源类型，低电压不会损坏电源或PIM。一个超范围电压将使PIM上的保险丝开路。

备件

127610-01交流电源模块

125840-01高电压交流电源输入模块(PIM)125840-02低电压交流电源输入模块(PIM)

106M1079-01 Universal AC Power Supply Module106M1081-01 Universal AC Power Input Module129486-01高压直流电源模块

129478-01高电压直流电源输入模块(PIM)133292-01低压直流电源模块

133300-01 低压直流电源输入模块PIM)。

3500/15交流和直流电源是半高模块，必须安装在机架左侧的指定插槽中。3500机架可以包含一个或两个具有任意交流和直流组合的电源。任一电源都可以为整个机架供电。

3500/15的3500/15交流和直流电源可接受各种高或低输入电压，并可转换为3500模块所需的电压。它们是机械保护系统的理想选择，如果需要备份，可以使用一个或两个电源。安装两个电源后，下方插槽容纳主电源，上方插槽容纳冗余电源。

3500/15电源可为3500提供交流或直流电源，包括瞬态数据接口(TDI)、单独的监控模块和输入/输出(I/O)模块以及机械保护和条件中的所有连接传感器监视系统。在不破坏机架的情况下，可以通过移除或插入任一电源模块来“热插拔”模块。

3500/15 BENTLY 半高电源模块 机械保护系统

BENTLY Bentley 3500/15 AC and DC power supply

The 350015 is a high-voltage ACIDC power module developed by Bently Nevada. This component is a half-height module and must be installed in the specified peg on the left side of the frame. This component is used as the power module Q for the Bentley Nevada Mechanical condition Monitoring system. Legacy 3500 AC power supply, high voltage AC PIM, and low voltage AC PIM are incompatible with general purpose AC power supply and PIM(power input module). The Legacy 3500 high voltage and low voltage DC power supply and PIM are incompatible with the Legacy 3500 high voltage and low voltage DC power supply and PIM.

The 3500 power supply is a half-height module that must be installed in a specially designed notch on the left side of the frame. The 3500 frame can be equipped with one or two power supplies (any combination of AC or DC). Any one of these power supplies can power the entire frame. If two power supplies are installed, the second power supply can be used as a backup of the first power supply. When two power supplies are installed, the upper power supply is used as the main power supply, and the lower power supply is used as the backup power supply. As long as one power supply is installed, removing or installing the second power module will not affect the operation of the frame. The 3500 power supply can accept a wide range of input voltages, and can convert the input voltage to other 3500 modules can accept the voltage.

For the 3500 mechanical protection system, there are three power supplies:

Ac power supply

2 High voltage DC power port

3. Low voltage DC power input power options:

175 to 264 Vac ms: (247 to 373 Vac,pk), 47 to 63 Hz. This option uses AC power and is a high voltage (usually 22OV) AC power input module (PIM). Ac power input modules (PIMs) installed before version R and/or power modules installed before version M require a voltage input of 175 to 250 Vac rms.

85 to 132 Vac ms: (120 to 188 Vac, pk)47 to 63 Hz. This option uses AC power and is low voltage (on

Normal 110V) AC power input module (PIM). Install AC power input modules (PIMs) before version R and/or power input modules before version M requiring voltage inputs :85 to 125Vac rms.

88 to 140 Vdc: This option uses DC power and is a high voltage DC power input module (PIM). 20 to 30 Vdc: This option is low voltage DC powered and is low voltage DC powered modyne (PIM).

Out-of-limit protection: For all power supply types, low voltage will not damage the power supply or PIM. An out-of-range voltage will open the fuse on the PIM.

Spare part

127610-01 AC power module

125840-01 High Voltage AC Power Input Module (PIM)125840-02 Low Voltage AC Power input Module (PIM)

106M1079-01 Universal AC Power Supply Module106M1081-01 Universal AC Power Input Module129486-01 HVDC power module

129478-01 High-voltage DC power input module (PIM)133292-01 Low-voltage DC power module

133300-01 Low Voltage DC power input module (PIM).

The 3500/15 AC and DC power supplies are half-height modules that must be installed in a designated slot on the left side of the rack. The 3500 rack can contain one or two power supplies with any combination of AC and DC. Either power supply can power the entire rack.

The 3500/15 AC and DC power supply of the 3500/15 accepts a variety of high or low input voltages and can be converted to the voltage required by the 3500 module. They are ideal for mechanical protection systems, and one or two power supplies can be used if backup is required. After the two power supplies are installed, the lower slot houses the primary power supply and the upper slot houses the redundant power supply.

The 3500/15 power supply provides AC or DC power to the 3500, including transient data interface (TDI), separate monitoring modules and input/output (I/O) modules, and all connected sensor monitoring systems in mechanical protection and conditions. Modules can be "hot-swappable" by removing or inserting either power module without damaging the rack.