BENTLY 3500-42M前置器/地震监测器

BENTLY 3500-42M前置器/地震监测器 

BENTLY 本特利内华达 3500/42M 前置器/地震监测器 

3500/42M proxim itor */地震监测器是一个4通道

接受近程和地震输入的监视器

传感器调节信号以提供各种振动

和位置测量，并比较条件化的

带有用户可编程报警的信号。

您可以使用3500框架对每个通道进行编程

组态软件执行以下功能:

%3E径向振动

%3E推力位置

%3E膨胀差

%3E偏心率

% 3E·雷巴姆*

%3E加速度

%3E速度

%3E轴绝对值

%3E循环接受区域

监控通道成对编程，最高可执行

一次两个上述功能。例如，频道1

和2可以执行一种功能，而通道3和4执行另一种功能

还是同样的功能。

3500/42M前置器*/地震的主要用途

监控旨在提供以下内容:

n通过持续比较监控的机械保护

驱动警报的配置警报设定点的参数

n操作和维护的基本机器信息

人事部门

根据配置，每个通道通常会调节

其输入信号产生的各种参数称为静态

价值观。您可以为每个活动静态配置报警设定点

任意两个活动静态的值和危险设定点

价值观念

完成电路连接并将代码上传到Arduino UNO后，就该连接了USB转RS-485模块在电脑上简单Modbus主机软件已安装。

打开设备管理器，根据您的PC检查USB转RS-485模块连接的COM端口，然后打开simple Modbus Master 8 . 1 . 1软件。

BENTLY 3500-42M前置器/地震监测器 

BENTLY Bentley Nevada 3500/42M preprocessor/seismic monitor cyclic redundancy check

The 3500/42M proxim itor */ seismic monitor is a 4-channel

A monitor that accepts short range and seismic inputs

The sensor adjusts the signal to provide a variety of vibrations

And position measurement, and comparison conditionalization

Signal with user programmable alarm.

You can program each channel using the 3500 framework

The configuration software performs the following functions:

%3E radial vibration

%3E thrust position

%3E expansion difference

%3E eccentricity

% 3E Raybam *

%3E acceleration

%3E speed

%3E axis absolute value

%3E loop accept area

Monitoring channels are programmed in pairs for maximum execution

Two of the above functions at once. For example, channel 1

And 2 can perform one function, while channels 3 and 4 perform another

It's the same function.

3500/42M preprocessor */ Main use for earthquakes

Monitoring aims to provide the following:

n Mechanical protection through continuous comparative monitoring

Configure the parameters that drive the alarm set point

n Basic machine information for operation and maintenance

Personnel department

Depending on the configuration, each channel is usually tuned

The various parameters generated by the input signal are called static

Values. You can configure alarm set points statically for each activity

Any two active static values and danger setpoints

Value concept

After completing the circuit connection and uploading the code to the Arduino UNO, it is time to connect the USB to RS-485 module. The simple Modbus host software has been installed on the computer.

Open the Device Manager, check the COM port connected to the USB to RS-485 module according to your PC, and then open the simple Modbus Master 8.1.1 software.

1. In... After simple Modbus software now opens write option.

BENTLY 3500-42M前置器/地震监测器