AO810V2  3BSE038415R1  |  模拟输入模块  |  CB220N  3KDE175613L2210 

产品型号：AO810V2

货号：3BSE038415R1

类别描述： 模拟输入模块

产品成色：全新，非全新

质保：一年

库存：有

品牌：ABB

尺寸

宽度 45毫米（1.77英寸）

深度 102 mm （4.01“）， 111 mm （4.37”） 包括连接器

高度 119毫米（4.7英寸）

重量 0.18 千克（0.4 磅）

详细数据

分辨率 14 位

隔离 分组与地面隔离

低于/超出范围 - / +15%

输出负载 ≤ 500 Ω（仅连接到 L1+ 的电源）

250 - 850 Ω（仅连接 L2+ 的电源）

错误 0 - 500 欧姆（电流）时最大 0.1%

温度漂移 典型值 30 ppm/°C，最大值 60 ppm/°C

上升时间 0.35 毫秒 （PL = 500 Ω）

更新周期时间 ≤ 2ms

电流限制 短路保护限流输出

最大现场电缆长度 600米（656码）

额定绝缘电压 50 伏

介电测试电压 500 V 交流电

AO810/AO810V2 模拟量输出模块有 8 个单极性模拟量输出通道。为了监控与D/A转换器的通信，串行数据被回读和验证。在回读期间接收到开路诊断。该模块周期性地执行自诊断。模块诊断包括过程电源监控，当输出电路的电源电压较低时，会报告该过程。该错误将报告为通道错误。通道诊断包括通道的故障检测（仅在活动通道上报告）。如果输出电流小于输出设定值且输出设定值大于 1 mA，则会报告错误。

特点和优势

8 通道 0...20 mA、4 至 20 mA 输出

OSP 在检测到错误时将输出设置为预定状态

模拟输出应短路至 ZP 或 +24 V

Product model: AO810V2

Item number: 3BSE038415R1

Category Description: Analog input module

Product color: new, not new

Warranty: One year

Stock: Yes

Brand: ABB

dimension

Width 45 mm (1.77 in)

Depth 102 mm (4.01 "), 111 mm (4.37 ") including connector

Height 119 mm (4.7 in)

Weight 0.18 kg (0.4 lb)

Detailed data

Resolution 14 bits

Isolation groups are isolated from the ground

Below/out of range - / +15%

Output load ≤ 500Ω (only connected to L1+ power supply)

250-850 Ω (Connect L2+ power supply only)

Maximum 0.1% for error 0-500 ohms (current)

The typical temperature drift is 30 ppm/°C and the maximum is 60 ppm/°C

Rise time 0.35ms (PL = 500Ω)

Update cycle time ≤ 2ms

Current limiting Short circuit protection Limited current output

Maximum field cable length 600 meters (656 yards)

Rated insulation voltage 50 volts

Dielectric test voltage 500 V AC

The AO810/AO810V2 analog output module has 8 unipolar analog output channels. To monitor communication with the D/A converter, serial data is read back and verified. An open circuit diagnosis was received during a read back. The module performs self-diagnosis periodically. Module diagnostics include process power monitoring, which is reported when the supply voltage to the output circuit is low. The error is reported as a channel error. Channel diagnostics include fault detection of channels (reported only on active channels). If the output current is less than the output set value and the output set value is greater than 1 mA, an error is reported.

Characteristics and advantages

8 channel 0... 20 mA, 4 to 20 mA output

The OSP sets the output to a scheduled state when an error is detected

Analog output should be shorted to ZP or +24 V