1336-L5 控制接口选项卡 可调频率交流驱动器

概述：

1336- l5是控制接口选项卡，是艾伦-布拉德利1336加可调频率交流驱动器的一部分。它特别适用于1336 Plus, 1336 Force和1336 Impact驱动器，特别是框架A-H驱动器，除了具有25 HP和30 HP额定功率的框架C驱动器。该控制接口板安装在主控板的底部，位于TB2端子带的顶部。1336-L5是一个24 VDC / 24 VAC逻辑板，用于接收额外的外部触点闭合信号。这些信号可以是任何电路，提供高=真逻辑状态，如硬连线电路，可编程逻辑控制器(PLC)输出模块，辅助触点，顺序器，以及提供24 VDC / VAC额定信号电压的类似电路。1366-L5有12个螺纹端子，设计用于连接2.1和0.30 mm2(14和22 AWG)铜线。紧固连接时，扭矩为0.90-1.13 N-m (8-10 lb. in.)。端子19和20用于启动/停止功能，端子19可编程接受状态、运行、前进和开始输入，而端子20可配置停止/故障复位信号。其他可以连接到控制接口板可用的TB3端子带的输入包括Reverse / Forward;慢跑;辅助和速度选择1-3个输入。该接口板支持2线制和3线制控制接线配置。其他可以通过控制接口板发起的命令有加速、减速、同步和遍历。

Allen-Bradley 1336- l5 +24伏交流/直流控制接口板是用于1336可调频率交流驱动器的逻辑控制接口选项板，它提供了连接各种驱动器命令和功能的手段。与所有其他逻辑接口板一样，该板位于主控板的A端口，它有9个控制输入，可以编程为任何选择的功能。为了正常工作，1336-L5逻辑控制接口板需要能够在高= true逻辑下工作的电路，并且需要24伏用户提供的交流/直流电压才能正常工作。该板还可以正常工作，电路在低状态下产生不超过8v DC/ 10v AC和1.5/2.5 mA，电压范围为+20至+26 v AC，高状态下每个输入源电流为10ma。1336-L5可用于编程各种驱动命令和功能，其中包括2个驱动加速/减速控制输入，允许用户选择驱动器使用的加速和减速时间。1336-L5也可用于本地控制，这使用户可以独家控制驱动逻辑，它还有助于控制前进/反转功能，控制反向和正向操作。该板还可用于控制其他各种驱动功能，如使能，通量使能，Jog，数字电位器，斜坡，复位和启动功能。1336-L5安装在主控板上J1跳线的2、3引脚和17、18引脚处，与1771-OB、-OQ、-OBB、-OBD、-OBN、-OQ16 PLC模块兼容。

内容来自www.xbaqingplc.com转载请标注

1336-L5 控制接口选项卡 可调频率交流驱动器

1336-L5 is the Control Interface TAB and is part of the Allen-Bradley 1336 plus adjustable frequency AC drive. It is particularly suitable for 1336 Plus, 1336 Force and 1336 Impact drives, especially frame A-H drives, in addition to Frame C drives with 25 HP and 30 HP power ratings. The control interface board is installed at the bottom of the main control board and on the top of the TB2 terminal belt. The 1336-L5 is a 24 VDC / 24 VAC logic board designed to receive additional external contact closure signals. These signals can be any circuit that provides a high = true logic state, such as hardwired circuits, programmable logic controller (PLC) output modules, auxiliary contacts, sequentiers, and similar circuits that provide a 24 VDC/VAC rated signal voltage. The 1366-L5 has 12 threaded terminals designed to connect 2.1 and 0.30 mm2(14 and 22 AWG) copper wires. The torque is 0.90-1.13N-m (8-10 lb.in.) when fastened. Terminals 19 and 20 are used for start/stop functions, terminals 19 can be programmed to accept status, run, forward, and start inputs, while terminals 20 can be configured with stop/fault reset signals. Other inputs that can be connected to the TB3 terminal tape available on the control interface board include Reverse/Forward; Jogging; Assist and speed select 1-3 inputs. The LPU supports 2-wire and 3-wire control cable configurations. Other commands that can be initiated through the control interface board are acceleration, deceleration, synchronization, and traversal.

Allen-Bradley 1336-L5 +24 volt AC/DC Control Interface Board is a logical control interface option board for 1336 adjustable frequency AC drives, which provides the means to connect various driver commands and functions. Like all other logical interface boards, this board is located on port A of the main control board, and it has 9 control inputs that can be programmed for any selected function. In order to function properly, the 1336-L5 logic control interface board needs a circuit that can operate with high = true logic and requires 24 volts of user-supplied AC/DC voltage to function properly. The board also works properly, with the circuit producing no more than 8v DC/ 10v AC and 1.5/2.5 mA at low state, with a voltage range of +20 to +26 v AC, and 10ma per input source at high state. The 1336-L5 can be used to program a variety of drive commands and functions, including 2 drive acceleration/deceleration control inputs that allow the user to select the acceleration and deceleration times used by the drive. The 1336-L5 is also available for local control, which gives the user exclusive control over the drive logic, it also helps to control the forward/reverse function, control the reverse and forward operations. The board can also be used to control various other drive functions such as enable, flux enable, Jog, digital potentiometer, ramp, reset and start functions. The 1336-L5 is installed at pins 2, 3 and 17, 18 of the J1 jumper on the main control board and is compatible with the 1771-OB, -OQ, -OBB, -OBD, -OBN, -OQ16 PLC modules.

1336-L5 控制接口选项卡 可调频率交流驱动器

1.因产品库存量大，没有搜到的型号，请联系我们。

2.所有售出的产品质量保证一年，如果您在收到货内

7天我们可以给您换货或退回任何质量问题。

3.我们是中国很好的工控产品供应商，如果您需要其他

 产品类型，请咨询我们，我们会立即给您答复。

4.如果您购买多件，我们会给您折扣，如果您已经收到价格，

请联系我们，我们将努力让您满意，我们的客户来自世界各地。